How do I fix my PetSafe collar

If Receiver Collar does not beep and the Test Light does not flash, replace the 10. battery in the Receiver Collar. If it still does not beep and the Test Light does not flash, contact the Customer Care Center at 1-800-732-2677. If the Receiver Collar beeps, there may be a complete or partial break in the 11.

Why is my petsafe shock collar not working?

If Receiver Collar does not beep and the Test Light does not flash, replace the 10. battery in the Receiver Collar. If it still does not beep and the Test Light does not flash, contact the Customer Care Center at 1-800-732-2677. If the Receiver Collar beeps, there may be a complete or partial break in the 11.

How do you reset a wireless dog collar?

Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on. Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off. Continue holding the button.

Do petsafe collars go bad?

If after changing batteries (and inserting them properly) there is no red LED illumination, then your collar may be bad. Before you call for a replacement, please verify you are using the right batteries and watch the video below further down this page.

Why is my electric dog collar not working?

Make sure your battery is charged in both the collar and the transmitter. Low battery charge can make for inconsistent functioning. Make sure both pieces are turned on and that the unit is properly synced so that the collar is receiving a signal from the transmitter.

Why is PetSafe collar blinking red?

Charging too often can reduce battery life. Charge your receiver collar when the receiver indicator light blinks red. The system works by sending a radio signal through a buried wire (boundary wire). Your pet wears a receiver collar that picks up the signal.

How do I test my PetSafe collar?

All you have to do is hold the tool against the contact points on your dog or cat’s receiver collar to check if the collar is working properly. The test light tool will light up if static correction is being activated. This accessory comes in most kits including a fence receiver collar, remote trainer, or bark collar.

How long should a PetSafe collar last?

The Wireless Containment System unit can last up to approximately 10 years or more if used properly. Batteries on the collar can last and be replaced up to 1 to 2 months.

How long do PetSafe rechargeable collars last?

The collar quickly charges in just 2-3 hours and lasts up to 3 weeks depending on frequency of use. The interchangeable design of the collar strap gives you the ability to customize your pet’s collar using any 3/4-inch non-metallic strap.

Why is my electric fence collar not working?

My pet’s Invisible Fence collar doesn’t activate at the boundary, what is wrong? Ensure that your pet’s Computer Collar receiver is fitted properly to his neck. The collar should be snug enough to slide only one finger between a correction post and your pet’s skin.

Article first time published on askingthelot.com/how-do-i-fix-my-petsafe-collar/

How do I know if my shock collar is working?

Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.

How do you check a dog's collar?

  1. Turn the Collar Receiver on.
  2. Hold the Test Light Contacts to the Contact Points.
  3. Press a Stimulation Button on the Remote Transmitter.
  4. The Test Light will flash.
  5. NOTE: At higher stimulation levels, the Test Light will flash brighter.
  6. Turn the Collar Receiver off.

How do I know my petsafe bark collar is working?

Check the tightness of the Bark Control Collar by inserting one finger between the end of a Contact Point and your dog’s neck. The fit should be snug but not constricting. 5. Allow your dog to wear the Bark Control Collar for several minutes then recheck the fit.

Why is my dog's collar flashing red?

If you have started to see a red flashing light on your pet’s Computer Collar unit, your Power Cap battery may need to be replaced. You can order replacement batteries online, from your local dealer, or by calling 1-800-824-3647.

Why is my dog invisible fence collar blinking green?

The status light will double flash green every 30 seconds during the 24-hour period after the dog has entered the boundary area. This feature monitors the voltage level of the battery. … If your light flashes double red, this indicates that your battery is low and your pet has challenged the dog containment system.

Will any PetSafe collar work?

In-Ground. Important: All PetSafe® In-Ground Fence™ collars are compatible with all PetSafe® In-Ground Fence systems except for the UltraSmart® and YardMax® systems. Locate the model number on the collar. … The model number on the collar should match one of the model numbers on the chart.

Can PetSafe collar get wet?

It’s water resistant! Can get wet but not submerged long.. we have a pond on property and I set the distance so he can only put his feet in then he gets the audible. Keeps him out when we are not home.

Are PetSafe wireless collars waterproof?

Petsafe Wireless Fence Collar – Waterproof Receiver – 5 Adjustable Levels of correction.

How do I know if my petsafe transmitter is bad?

To check if the transmitter is having issues you’ll need to disconnect the existing boundary wire and connect a short 15-foot section of boundary wire to run some tests. Make sure the 15-foot wire is spread out. The signal will cancel anywhere the wire is within 3 feet of itself.

How do I turn my invisible fence collar on?

  1. Push the button on the receiver. A light on the receiver will flash. …
  2. Adjust the distance from the boundary wire to trigger a warning alarm. Most transmitter boxes have a knob or lever to use to change the distance. …
  3. Change the metal prongs on the receiver.

How do you reset an electric dog fence?

Resetting the system can be as simple as replacing the batteries in your transmitter. Bring your dog inside, and turn off the power to the fence. Unplug the transmitter. Look for metal objects around or on top of the fence.

What do you do if your dog won't wear a cone?

Reward with a treat any time your dog shows interest in the cone. Any time they sniff, touch it with their nose, or even look at it, praise and give a treat. Keep this session short and fun. Repeat as necessary until your dog shows no fear or stress when in the presence of the cone.

What do you do if your dog's cone doesn't work?

Five Different Types of Alternatives to Dog Cones: Inflatable collars: allow more movement and a comfier fit. Neck control collars: restrict movement more than soft e-collars but like inflatable collars interfere less with peripheral vision and ears. Surgical recovery clothing: not a cone!

What can I use instead of a cone for my cat?

  • The BiteNot Collar. This device does not represent the shape of a cat or dog cone at all; it most resembles a neck brace. …
  • The ProCollar Premium Protective Collar. …
  • Kong EZ Soft Collar. …
  • Comfy Collar. …
  • The Boobooloon. …
  • Optivisor or Novaguard. …
  • TCOA Soft E-Fabric Collar.

How do you turn on a petsafe shock collar?

Use the Dog 1/2 button on the remote to select either Dog 1 or Dog 2. With the remote turned on and the collar turned off, press and hold the on/off button on the collar. 2. After about 5 seconds the LED on collar will turn off indicating that it is ready for pairing.

Why is my dog's bark collar not working?

Make sure the collar is properly placed high on your dog’s neck close to the ears with the contact points touching the center of your dog’s neck. Tighten the NoBark and make sure the contact points touch his skin. … If your dog still does not respond, contact the Customer Care Center at 1-800-732-0144.